![danscourses router on a stick danscourses router on a stick](https://ccna-200-301.online/wp-content/uploads/2020/06/Router-on-a-Stick-Example.png)
- #Danscourses router on a stick how to
- #Danscourses router on a stick generator
- #Danscourses router on a stick update
- #Danscourses router on a stick simulator
- #Danscourses router on a stick download
#Danscourses router on a stick simulator
#Danscourses router on a stick download
Free Packet Tracer Download - Thank you /u/tenormore for pointing it out.Free CCNA training by reddit backed kickstarter created by Andrew Crouthamel.Internetwork Training CCNA Practice Quiz - I like this one a lot of good questions.Free CCNA Workbook - By Matthew George, CCIE #38216.Cisco's Learning Network - I would look here no matter what you do.
#Danscourses router on a stick update
Packet Life Cheat Sheets - Don't forget to thank /u/stretch85 and remind him to update his sheets.- Subnetting practice site built by redditor /u/DressedUpNowhere2Go.
#Danscourses router on a stick generator
#Danscourses router on a stick how to
That’s it, this how to configure the router on a stick inter VLAN routing. %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.2, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0.2, changed state to up %LINEPROTO-5-UPDOWN : Line protocol on Interface FastEthernet0/0.1, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0.1, changed state to up %LINEPROTO-5-UPDOWN : Line protocol on Interface FastEthernet0/0, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up Router(config-if)#no shutdown (Enabling the fast ethernet port f0/0) Router(config)#int f0/0 (Selecting f0/0 port) Router#conf t (Entering configuration mode) %SYS-5-CONFIG_I: Configured from console by console Router(config-subif)#ip address 20.0.0.1 255.0.0.0 (Assigning IP Address to the sub-interface port f0/0.2) Router(config-subif)#encapsulation dot1q 20 (Assigning the sub-interface port f0/0.2 to VLAN 20. Router(config)#int f0/0.2 (Creating and selecting sub-interface port “ f0/0.2” on f0/0) Router(config-subif)#ip address 10.0.0.1 255.0.0.0 (Assigning IP Address to the sub-interface port f0/0.1) Router(config-subif)#encapsulation dot1q 10 (Assigning the sub-interface port f0/0.1 to VLAN 10. Router(config)#int f0/0.1 (Creating and selecting sub-interface port “ f0/0.1” on f0/0) Router#conf t (entering configuration mode)
![danscourses router on a stick danscourses router on a stick](https://www.interfacett.com/wp-content/uploads/2014/08/001-network-diagram-Cisco-Router.png)
Switch(config)# CONFIGURE ROUTER ON A STICK Switch(config)#do copy run start (Save switch configuration) Switch(config-if)#switchport mode trunk (Configuring port 3 as trunk) Switch(config-if)#int f0/3 (Selecting port 3 of the switch) Switch(config-if)#switchport access vlan 20 (Assigning port 2 to VLAN 20) Switch(config-if)#int f0/2 (Selecting port 2 of the switch) Switch(config-if)#switchport access vlan 10 (Assigning port 1 to VLAN 10) Switch(config)#int f0/1 (Selecting port 1 of the switch) Switch(config-vlan)#name sales (Assigning name to VLAN)
![danscourses router on a stick danscourses router on a stick](https://www.techreally.com/wp-content/uploads/2013/11/cisco-labs-770x430.png)
Switch(config-vlan)#vlan 20 (Creating VLAN 20) Switch(config-vlan)#name production (Assigning name to VLAN) Switch(config)#vlan 10 (Creating VLAN 10) Switch#conf t (entering configuration mode)Įnter configuration commands, one per line. (Note: The text in black is the command used to configure inter VLAN, text in blue indicates the output and text in green indicate the uses of the command. We are going to configure the router on a stick according to the below-given diagram.įirst of all, let’s configure VLAN on the switch The router on a stick is the virtual LAN configuration which allows you to add multiple VLAN to the single port of the router. In a normal scenario, if you want to add 10 VLAN to the router means you must need at least 10 physical port to the router, Am I right. It allows you to add multiple VLAN to the router with the help of a single port. This is the most popular concept in Virtual LAN configuration. In this post, we are going to learn how to configure Router on a stick ( Inter VLAN Routing).